Whirlpool Washer Error Code F21 — Long Drain
F02.)What the code means
F21 is Whirlpool's long-drain fault. The control board runs the drain pump and watches the water level sensor; if the level has not dropped after roughly 8 minutes of pumping, the cycle stops and F21 is displayed. The machine is draining — just too slowly — which is why this code is about restriction first and parts second. F21 appears on Whirlpool Duet, Duet Sport, and later WFW-series front-load washers, and on the Kenmore front-loaders built by Whirlpool on the same platform.
Likely causes, in the order to check them
- Clogged drain pump filter (most common). The filter — Whirlpool calls it a coin trap — catches everything that leaves pockets. A sock, coins, or a lint mat can cut the flow enough to trip F21.
- Kinked, clogged, or badly installed drain hose. A hose pinched behind the machine, or pushed too far into the standpipe (which can make the washer siphon water back in as fast as it pumps it out).
- Excess suds. Too much detergent, or non-HE detergent in an HE machine, foams up and fools the water level sensor into thinking the tub is still full.
- Something jammed in the pump. A bobby pin or screw can wedge against the impeller behind the filter — the filter looks clean, but the pump cannot turn freely.
- A failing drain pump. The motor weakens with age and hard water. This is the part to replace only after the free checks above.
- Water level (pressure) sensor or its hose (least common). If the sensor is stuck reading "full," the washer keeps pumping and times out even with an empty tub.
Step-by-step fix
- Unplug the washer. Note how much water is left in the tub — a full tub tells you the drain barely worked at all.
- Check the drain hose first (2 minutes, no tools). Pull the washer out enough to see the hose: no kinks, no crush points. At the standpipe or laundry tub, the hose end should sit only a few inches into the drain — not shoved deep and not sealed airtight. The top of the drain loop should be within the height range in your model's installation guide.
- Clean the drain pump filter. On most Whirlpool front-loaders it is behind a small access door at the bottom front. Put a shallow pan and towels down, open the door, and use the small drain hose (if fitted) to empty the filter housing first. Then unscrew the filter counterclockwise, slowly — water will come out. Clear lint, coins, and debris, rinse the filter, and check the housing behind it for anything jammed against the pump impeller. Reinstall the filter snugly.
- If suds are suspect, run a rinse. If the failed load used a lot of detergent or non-HE detergent, run an empty rinse-and-spin (or drain-and-spin) cycle with no detergent. If F21 clears and stays cleared, suds were the problem — switch to HE detergent at the recommended dose.
- Test with a drain & spin cycle. Listen at the bottom of the machine: you should hear the pump hum steadily and water flow out. A steady hum with slow flow means a restriction remains. A loud buzzing or grinding suggests something in the pump. Silence means the pump is not running at all.
- Test the pump before replacing it (optional, multimeter). With the washer unplugged and the pump accessible, disconnect its two wire terminals and measure resistance across them. These pumps typically read in the 10–30 Ω range; an open (OL) or near-zero reading means the motor winding has failed. Confirm the exact specification in your model's tech sheet.
The part involved
If the path is clear and the pump has failed, the replacement on most Whirlpool front-load models in this family (Duet, Duet Sport, WFW-series, and Whirlpool-built Kenmore front-loaders) is the drain pump assembly, Whirlpool part 280187 (also sold as WP280187; PartSelect number PS1485610). Parts retailers list this exact pump for the "won't drain / F21" fault across several hundred models in the family. Always confirm against your model number before ordering — later Whirlpool front-loaders use a different pump.
Whirlpool Drain Pump Assembly 280187 — buy links for PartSelect and RepairClinic will appear here once our affiliate accounts are active. Until then, search part number 280187 at your preferred parts retailer and verify fit with your model number.
Difficulty and cost picture
Filter cleaning: easy, no tools, about 15 minutes. Pump replacement on this family: a moderate DIY job — the pump is reached from the front or bottom panel on most models, with two wire terminals and hose clamps. Professional repair for a failed pump typically runs in the $150–$450 range (parts and labor) per published 2026 repair-cost guides, which is why the free checks come first.
When to call a pro
- The pump tests good but never receives power — that points to wiring or the control board.
- F21 returns immediately after a verified-clear filter, hose, and pump.
- You see water leaking from the pump housing or tub-to-pump hose.
- You are not comfortable working under a machine with residual water in it.
Newer Whirlpool models show this same fault as F9 E1 — see our F9 E1 guide. If your code is about filling instead of draining, see F8 E1 (low water flow).
Sources
- Whirlpool long-drain definition and ~8-minute window, F21/F02 equivalence — repair references citing Whirlpool's error code lists: Oh So Spotless, "Whirlpool Washer Error Codes"; Nick's Appliance Repair, "Whirlpool Washer Error Codes — Complete List & Fixes." Checked November 2026.
- Causes and fix order (filter, hose, suds, pump) — ErrorCodePedia, "Whirlpool Washer Error F21: Causes, Fixes and Repair Cost (2026)"; HomeApplianceFixing, "Whirlpool Error Code F21" (pump resistance range). Checked November 2026.
- Part 280187 verification and model fit — AppliancePartsPros catalog page for Whirlpool 280187 Drain Pump Assembly (AP3953640); PartSelect.ca, Drain Pump Kit 280187 (PS1485610) expert Q&A. Checked November 2026.
Some links on this page may become affiliate links; see our affiliate disclosure. FixCode HQ is not affiliated with Whirlpool.